3. Pump Repair Kits by Brand
-
Scot 118.000.383 Repair Kit — Motorpump 57 / 57E
Scot 118.000.383 Repair Kit — Motorpump 57 / 57E
Item #N/A
Scot 118.000.383 Repair Kit — Motorpump 57 Seal Kit
The Scot 118.000.383 repair kit is the service kit for Scot Motorpump 57 and 57E. These models use a 1-1/2? Type 21 seal arrangement rather than the standard arrangement found across the rest of the JM-frame line, so they take this kit and not the 118.000.344. Supplied complete, and built to OEM-equivalent standards or higher.
What’s included:
-
Mechanical seal
-
Shaft sleeve
-
Gasket & O-rings
-
Five stainless steel hard parts for corrosion-resistant durability
-
P-80 Emulsion Rubber Lubricant
Applications:
The Motorpump 57 and 57E are the higher-duty end of the Scot JM-frame line, run at 1150, 1750 and 3500 RPM in commercial heating and chilled water circulation, domestic water boosting and process water service. Faster shaft speeds and longer duty cycles are hard on a seal, which is what makes the material choice below worth a moment’s thought on this model in particular.
The Scot 118.000.383 repair kit fits the 1-1/2? Type 21 seal on Motorpump 57 and 57E.
-
Motorpump 57 — 1150, 1750 and 3500 RPM
-
Motorpump 57E — 1750 RPM
-
Frames: JM145 through JM215
Note: Every other Motorpump size in this frame range — 50, 52, 53, 54, 55, 65 and 81 — uses a different seal arrangement and takes the 118.000.344 kit instead. Verify your pump nameplate, motor and frame at checkout so we can confirm the correct kit.
Three kits available
Same kit, same fit — the difference is the seal material inside. Choose your build from the dropdown above.
-
Standard – Carbon/Ceramic/Nitrile — ordinary hot water and chilled water systems
-
Upgrade – Carbon/Ceramic/Viton — hotter systems, glycol and chemicals
-
Upgrade – Silicon Carbide/Viton — gritty water and hard-wearing duty
Which kit do I need?
Most Motorpump 57 installations take the Standard Kit. Step up to an Upgrade Kit if your system runs hotter, carries glycol or chemicals, handles gritty water, or the pump runs at 3500 RPM on a long duty cycle.
Kit Max °F Choose This If Standard – Carbon/Ceramic/Nitrile 200°F Clean water at neutral pH — ordinary HVAC, booster and general water service. This is the standard build and matches the original kit. Upgrade – Carbon/Ceramic/Viton 450°F Your system runs hot, or carries glycol, bleach or other chemicals that break down standard Nitrile. Upgrade – Silicon Carbide/Viton 450°F Gritty or dirty water, process water, or any duty where seals keep wearing out early. Hardest faces we offer. Still not sure? Text a photo of your pump nameplate to 561-414-1046 and tell us what the system runs — we’ll tell you which build to order. No purchase required.
Rebuilding a Scot pump?
We stock repair kits for the Scot JM-frame range, in all three seal material builds.
Not sure which seal material your system needs? Read How to Choose the Right Mechanical Seal Materials for Your Pump Application.
Have questions? Call us anytime-we’re here to help
Explore our full line up of Pump Repair Kits
Looking for more? Check out our Shaft seals, Parts/Accessories & OEM seals
Sta-Rite D-Series Pump Repair Kit — Seal, Sleeve, Diffuser Ring & Gasket
Sta-Rite D-Series Pump Repair Kit — Seal, Sleeve, Diffuser Ring & Gasket
Item #STA-D-KIT
Sta-Rite D-Series Pump Repair Kit — Seal, Sleeve, Diffuser Ring & Gasket
This Sta-Rite D-series pump repair kit bundles the four parts you replace at a standard seal service into one kit — the mechanical seal, shaft sleeve, diffuser ring, and housing gasket. Built to OEM-equivalent standards or higher for a complete, correct rebuild of your Sta-Rite D-series pump. Also fits Berkeley and Pentair equivalents.
What’s Included
-
Mechanical seal — PS-3883, 1-1/4″, John Crane 2100/2106 style (Sta-Rite U9-433SS / U109-220)
-
Shaft sleeve — C23-58 (2358), stainless steel, 1.000″ ID × 1.250″ OD × 2.285″, with O-ring
-
Diffuser ring — C21-2 (D/ED-series diffuser ring)
-
Housing gasket — C20-46 (C2046), vellumoid, ID 7.937″ × OD 9.625″
Applications
Built for the Sta-Rite D-series pump seal service — everything you need to reseal the pump in one kit, instead of sourcing four parts separately. Matching from a worn pump or a parts list? Confirm your pump model and frame from the nameplate before ordering, or send a photo to info@sealhouseusa.com, or call/text 561-414-1046. No purchase required — our seal specialists will match it.Why Buy the Kit
Ordering the seal, sleeve, diffuser ring, and gasket together as a kit means every part matches the same pump service, arrives together, and saves you sourcing them one at a time. Prefer to buy a single part? Each is available separately — see the individual product links below.
Have questions? Call us anytime-we’re here to help
Explore our full line up of Pump Repair Kits
Looking for more? Check out our Shaft seals, Parts/Accessories & OEM seals
Stancor Pump Repair Kit — P20, P40, P50 & P70
Stancor Pump Repair Kit — P20, P40, P50 & P70
Item #N/A
Stancor Pump Repair Kit — P20, P40, P50 & P70
Stancor pump repair kits for the P20, P40, P50, and P70 submersible pumps — choose your model from the dropdown for the correct seal and O-ring kit. Each is built to OEM-equivalent standards or higher to reseal your Stancor pump. Choose your pump model from the dropdown menu above:
What’s Included by Model:
-
P20 — 18mm mechanical seal, O-ring, and seal rings.
-
P40 — 18mm mechanical seal, O-ring, and seal rings.
-
P50 — upper and lower seals (20mm), O-ring kit, and seal rings. The lower is a 20mm welded metal bellows seal; the upper is a 20mm MG9. (Lower seal is a special-order item — see note.)
-
P70 — upper and lower seals (32mm), O-ring kit, and seal rings. The lower is a 32mm welded metal bellows seal; the upper is a 32mm seal.
Special Order — P50 Lower Seal
The P50’s lower seal (20mm welded metal bellows) is a special-order item and may carry a lead time. If you need the P50 kit, call or text 561-414-1046 or email info@sealhouseusa.com to confirm availability and timing before ordering.Applications
Built for Stancor submersible pumps at a standard seal service. Matching from a worn kit or a parts list? Confirm your pump model and serial from the nameplate before ordering, or send a photo to info@sealhouseusa.com, or call/text 561-414-1046. No purchase required — our seal specialists will match it.
Explore our full line up of OEM seals
Looking for more? Shop Pump Repair Kits, Shaft Seals and Pre-Cut Gaskets
Have questions? Call us anytime- we’re here to help
Sulzer ABS AFP Repair Kit — #61702006 (Seals, O-Rings & Seal Rings)
Sulzer ABS AFP Repair Kit — #61702006 (Seals, O-Rings & Seal Rings)
Item #SLZ-AFP-61702006
Sulzer ABS AFP Repair Kit — #61702006 (Seals, O-Rings & Seal Rings)
The ABS AFP repair kit (Sulzer #61702006) is a complete seal and O-ring service kit for Sulzer ABS AFP submersible pumps, including the — ET-SET AFP M5 375 GLRD 80/65 applications. Built to OEM-equivalent standards or higher, it supplies the seals and O-rings you replace at a seal service for the same fit and reliability as the original. Bearings are available separately on request.
At-a-Glance:
-
Sulzer ABS kit number: 61702006
-
Kit type: Seal and O-ring service kit
-
Fits: ABS ET-SET AFP M5 375 GLRD 80/65
-
Mechanical seals: 11110050 and 11100053
-
Form: Seal and O-ring service kit
-
Bearings: Not included — available on request
What’s Included:
-
Mechanical seals — 11110050 and 11100053
-
Seal rings
-
O-rings
Bearings
Bearings are not included in the standard kit, but we can supply them for your AFP pump on request. Add them to your order by calling or texting 561-414-1046, or email info@sealhouseusa.com and we’ll match the correct bearings for your pump.Applications
The Sulzer ABS AFP is a submersible sewage and wastewater pump used in municipal and industrial lift-station service. This kit fits the ET-SET AFP M5 375 GLRD 80/65 and covers the parts replaced at a standard seal service. Matching from a worn kit or an old parts list? Confirm your full pump model and serial from the nameplate before ordering, or send a photo to info@sealhouseusa.com, or call/text 561-414-1046. No purchase required — our seal specialists will match it.
Explore our full line up of Sulzer ABS Pump Repair Kits
Looking for more? Check out our Mechanical seals, Parts/Accessories & OEM seals
Have questions?- Call us anytime-we’re here to help
Sulzer ABS AFP Repair Kit — #61705000(MM) / 61705024 (Seals, O-Rings & Hardware)
Sulzer ABS AFP Repair Kit — #61705000(MM) / 61705024 (Seals, O-Rings & Hardware)
Item #61705000
Sulzer ABS AFP Repair Kit — #61705000 / 61705024 (25mm Seals & O-Rings)
The ABS AFP repair kit (Sulzer #61705000 (D) / 61705024) is a complete seal and O-ring service kit for Sulzer ABS AFP submersible pumps — the AFP M13/6–M40/2 (50Hz) and AFP M15/6–M35/4 (60Hz). Built to OEM-equivalent standards or higher, it supplies the sealing and hardware components you replace at a seal service for the same fit and reliability as the original. Bearings for a full overhaul are available separately on request.
At-a-Glance:
-
Sulzer ABS kit numbers: 61705000 (D) and 61705024
-
Fits: ABS AFP M13/6–M40/2 (50Hz), AFP M15/6–M35/4 (60Hz)
-
Seal size: 25mm (two mechanical seals)
-
Seal Faces: Carbon/Stainless Steel upper · Silicon Carbide/Silicon Carbide lower
-
Kit type: Seal and O-ring service kit
-
Bearings: Available on request (not included as standard)
What’s Included:
-
Two 25mm mechanical seals with snap rings — upper 11100028, lower 11110095 (Carbon/Ceramic upper, Silicon Carbide/Silicon Carbide lower)
-
Seal rings
-
O-rings
Bearings
Bearings are not included in the standard kit, but we can supply them for your AFP pump on request. Add them to your order by calling or texting 561-414-1046, or email info@sealhouseusa.com and we’ll include the correct bearings for your pump.Applications
The Sulzer ABS AFP is a submersible sewage and wastewater pump used in municipal and industrial lift-station service. This kit fits the AFP M13/6–M40/2 (50Hz) and AFP M15/6–M35/4 (60Hz) and covers the parts replaced at a standard seal overhaul. Matching from a worn kit or an old parts list? Confirm your full pump model and serial from the nameplate before ordering, or send a photo to info@sealhouseusa.com, or call/text 561-414-1046. No purchase required — our seal specialists will match it.
Explore our full line up of Pump Repair Kits
Looking for more? Check out our Mechanical seals, Parts/Accessories & OEM seals
Have questions?- Call us anytime-we’re here to help
Sulzer ABS AFP-ME4N Repair Kit — #61702052 (Upper & Lower Seals + O-Ring Kit)
Sulzer ABS AFP-ME4N Repair Kit — #61702052 (Upper & Lower Seals + O-Ring Kit)
Item #61702052
Sulzer ABS AFP-ME4N Repair Kit — #61702052 (Seals & O-Rings)
The ABS AFP-ME4N repair kit (Sulzer #61702052) is a complete seal and O-ring service kit for Sulzer ABS AFP-ME4N submersible pumps. Built to OEM-equivalent standards or higher, it supplies the sealing and hardware components you replace at a seal service for the same fit and reliability as the original. Bearings for a full overhaul are available separately on request.
At-a-Glance:
-
Sulzer ABS kit number: 61702052
-
Fits: ABS AFP-ME4N submersible pumps
-
Seal Faces: Carbon/Ceramic upper · Silicon Carbide/Silicon Carbide lower
-
Kit type: Seal and O-ring service kit
-
Bearings: Available on request (not included as standard)
What’s Included:
-
Mechanical seals — 11110173 (65mm) and 11110135 (55mm)
-
Sealing rings
-
O-rings
-
Snap ring
-
Oil Seal
Bearings
Bearings are not included in the standard kit, but we can supply them for your AFP-ME4N on request. Add them to your order by calling or texting 561-414-1046, or email info@sealhouseusa.com and we’ll include the correct bearings for your pump.Applications
The Sulzer ABS AFP-ME4N is a submersible sewage and wastewater pump used in municipal and industrial lift-station service, and this kit covers the parts replaced at a standard seal overhaul. Matching from a worn kit or an old parts list? Confirm your full pump model and serial from the nameplate before ordering, or send a photo to info@sealhouseusa.com, or call/text 561-414-1046. No purchase required — our seal specialists will match it.
Explore our full line up of Pump Repair Kits
Looking for more? Check out our Mechanical seals, Parts/Accessories & OEM seals
Have questions?- Call us anytime-we’re here to help
Sulzer ABS AFPK Repair Kit — #61705055 (Seals, O-Rings & Seal Rings)
Sulzer ABS AFPK Repair Kit — #61705055 (Seals, O-Rings & Seal Rings)
Sulzer ABS AFPK Repair Kit — #61705055 (Seals, O-Rings & Seal Rings)
The ABS AFPK repair kit (Sulzer #61705055) is a complete seal and O-ring service kit for Sulzer ABS AFPK submersible pumps, including the AFPK 1048.3-ME300/2 FM. Built to OEM-equivalent standards or higher, it supplies the seals and O-rings you replace at a seal service for the same fit and reliability as the original. Bearings are available separately on request.
At-a-Glance:
-
Sulzer ABS kit number: 61705055
-
Kit type: Seal and O-ring service kit
-
Fits: ABS AFPK 1048.3-ME300/2 FM
-
Mechanical seals: 11000083 and 11100093
-
Form: Seal and O-ring service kit
-
Bearings: Not included — available on request
What’s Included:
-
Mechanical seals — 11000083 and 11100093
-
Seal rings
-
O-rings
Bearings
Bearings are not included in the standard kit, but we can supply them for your AFPK pump on request. Add them to your order by calling or texting 561-414-1046, or email info@sealhouseusa.com and we’ll match the correct bearings for your pump.Applications
The Sulzer ABS AFPK is a submersible sewage and wastewater pump used in municipal and industrial lift-station service, and this kit covers the parts replaced at a standard seal service. Matching from a worn kit or an old parts list? Confirm your full pump model and serial from the nameplate before ordering, or send a photo to info@sealhouseusa.com, or call/text 561-414-1046. No purchase required — our seal specialists will match it.
Explore our full line up of Sulzer ABS Pump Repair Kits
Looking for more? Check out our Mechanical seals, Parts/Accessories & OEM seals
Have questions?- Call us anytime-we’re here to help
Sulzer ABS Piranha PE1 Repair Kit — #61705079 (Seals, O-Rings & Seal Rings)
Sulzer ABS Piranha PE1 Repair Kit — #61705079 (Seals, O-Rings & Seal Rings)
Item #SLZ-PIRANHA-PE1-61705079
Sulzer ABS Piranha PE1 Repair Kit — #61705079 (Seals, O-Rings & Seal Rings)
The ABS Piranha PE1 repair kit (Sulzer #61705079) is a complete seal and O-ring service kit for Sulzer ABS Piranha PE1 grinder pumps. Built to OEM-equivalent standards or higher, it supplies the seals and O-rings you replace at a seal service for the same fit and reliability as the original. Bearings are available separately on request.
At-a-Glance:
-
Sulzer ABS kit number: 61705079
-
Kit type: Seal and O-ring service kit
-
Fits: ABS Piranha PE1 grinder pumps
-
Mechanical seals: 11110197 and 11100106
-
Seal rings: 11130003
-
Form: Seal and O-ring service kit
-
Bearings: Not included — available on request
What’s Included:
-
Mechanical seals — 11110197 and 11100106
-
Seal rings — 11130003
-
O-rings
Bearings
Bearings are not included in the standard kit, but we can supply them for your Piranha PE1 on request. Add them to your order by calling or texting 561-414-1046, or email info@sealhouseusa.com and we’ll match the correct bearings for your pump.Applications
The Sulzer ABS Piranha PE1 is a submersible grinder pump used in pressurized sewage and wastewater systems, and this kit covers the parts replaced at a standard seal service. Matching from a worn kit or an old parts list? Confirm your full pump model and serial from the nameplate before ordering, or send a photo to info@sealhouseusa.com, or call/text 561-414-1046. No purchase required — our seal specialists will match it.
Explore our full line up of Sulzer ABS Pump Repair Kits
Looking for more? Check out our Mechanical seals, Parts/Accessories & OEM seals
Have questions?- Call us anytime-we’re here to help
Sulzer ABS Piranha PE2 Repair Kit — #61705080 (Upper & Lower Seals + O-Ring Kit)
Sulzer ABS Piranha PE2 Repair Kit — #61705080 (Upper & Lower Seals + O-Ring Kit)
Item #SH61705080
Sulzer ABS Piranha PE2 Repair Kit — #61705080 (Upper & Lower Seals + O-Ring Kit)
The ABS Piranha PE2 repair kit (Sulzer #61705080) is a complete seal and O-ring service kit for Sulzer ABS Piranha PE2 grinder pumps. Built to OEM-equivalent standards or higher, it supplies the seals and O-rings you replace at a seal service for the same fit and reliability as the original. Bearings and hardware are available separately on request.
At-a-Glance:
-
Sulzer ABS kit number: 61705080
-
Fits: ABS Piranha PE2 grinder pumps
-
Upper seal: 11100108 — 35mm, Silicon Carbide/Silicon Carbide (SiC/SiC)
-
Lower seal: 11110096 — 30mm, Silicon Carbide/Silicon Carbide (SiC/SiC)
-
Kit type: Seal and O-ring service kit
-
Bearings: Available on request (not included as standard)
What’s Included:
-
Upper mechanical seal — 11100108, 35mm (SiC/SiC)
-
Lower mechanical seal — 11110096, 30mm (SiC/SiC)
-
O-ring kit
Bearings & Hardware
Bearings and hardware are not included in the standard kit, but we can supply them for your Piranha PE2 on request. Add them to your order by calling or texting 561-414-1046, or email info@sealhouseusa.com and we’ll match the correct parts for your pump.Applications
The Sulzer ABS Piranha PE2 is a submersible grinder pump used in pressurized sewage and wastewater systems, and this kit covers the parts replaced at a standard seal service. Matching from a worn kit or an old parts list? Confirm your full pump model and serial from the nameplate before ordering, or send a photo to info@sealhouseusa.com, or call/text 561-414-1046. No purchase required — our seal specialists will match it.
Explore our full line up of Sulzer ABS Pump Repair Kits
Looking for more? Check out our Mechanical seals, Parts/Accessories & OEM seals
Have questions?- Call us anytime-we’re here to help
-